Furnace size calculator

Enter your home’s heated area and pick your climate. You’ll get the heat your home needs and the furnace input rating to shop for.

Heat your home needs

95,000 BTU per hour

Furnace input rating
100,000 BTU per hour
Nearest standard size
100,000 BTU

Shop for this project

As an Amazon Associate, Measure the Dream earns from qualifying purchases.

How it works

A common rule of thumb sizes heating by floor area: roughly 30 to 35 BTU per square foot in the warmest US climate zones, rising to 50 to 60 in the coldest. The calculator uses the middle of the range for your zone, then adjusts for ceilings taller or shorter than 8 feet and for insulation that’s better or worse than average.

That’s the heat your home needs. Furnaces are sold by their input rating, the fuel they burn, and an 80% efficient furnace only delivers 80% of it as heat. So the calculator divides by the efficiency (AFUE) and rounds up to the next common furnace size.

Example

With heated area 2,000 sq ft, climate: zone 5: cold (Ohio, Illinois, New England), average ceiling height 8 ft, insulation: average, furnace efficiency (AFUE): 95% (high efficiency), the answer is 95,000 BTU per hour.

How to measure

Use the heated floor area of the home and pick your climate zone. The calculator multiplies the area by a typical heat loss per square foot for that zone, adjusts for ceiling height and insulation, then works out the furnace’s input rating from its efficiency.

Treat the result as a cross-check. A Manual J calculation from a contractor is the right way to size a furnace, and it’s worth asking for one before replacing a unit like for like.

Furnace input rating by home size and climate

Nearest standard furnace size (input rating), for a 95% efficient furnace, 8 ft ceilings and average insulation.

Home sizeHot (zone 1–2)Mixed (zone 4)Cold (zone 5)Very cold (zone 6–7)
1,000 sq ft40,000 BTU60,000 BTU60,000 BTU60,000 BTU
1,500 sq ft60,000 BTU80,000 BTU80,000 BTU100,000 BTU
2,000 sq ft80,000 BTU100,000 BTU100,000 BTU120,000 BTU
2,500 sq ft100,000 BTU120,000 BTU140,000 BTUOver 140,000 BTU
3,000 sq ft120,000 BTU140,000 BTUOver 140,000 BTUOver 140,000 BTU

Common mistakes

  • Replacing like for like. Many older furnaces were oversized, and homes that have had new windows or insulation since need less heat.
  • Mixing up input and output. Furnaces are labeled by input BTU. Output is input × efficiency, so a 100,000 BTU, 80% furnace delivers about 80,000.
  • Oversizing for comfort. A bigger furnace heats in short bursts, which is noisier and less even, not warmer.
  • Forgetting about venting. Moving from an 80% to a 90%+ furnace usually means new PVC venting and a condensate drain.

Tips before you buy

  • This is an estimate for budgeting and comparing quotes. A contractor should size the final unit with a Manual J load calculation, which accounts for your windows, walls and air leaks.
  • Oversized furnaces cycle on and off often, which wastes fuel and wears them out faster. Bigger isn’t better.
  • If you’re replacing an old furnace, don’t just match its size. Many older homes have oversized units, and added insulation or new windows reduce the load.
  • Sealing air leaks and adding attic insulation can cut the size you need.

Common questions

What size furnace do I need for a 2,000 square foot house?

In a cold climate (zone 5) with average insulation, about 95,000 BTU of heat, which is a 100,000 BTU input furnace at 95% efficiency. In a warm climate (zone 3), about 75,000 BTU of heat, or an 80,000 BTU furnace.

What is AFUE?

Annual fuel utilization efficiency: the share of the fuel a furnace burns that becomes heat in your home. A 95% AFUE furnace turns 95% of its fuel into heat.

How many BTU per square foot do I need to heat a house?

Roughly 30 to 35 in the hottest US climates, 40 to 50 in mixed and cold climates, and 50 to 60 in the coldest, for a house with average insulation and 8-foot ceilings.

Add this calculator to your website

Free for any site or blog. Paste this code where you want the calculator to appear. The short script makes it resize to fit; if your site doesn’t allow scripts, the calculator still works without it.